Wire

Modified by Susan Riege on Aug 17, 2018
Contents

Parent page: Schematic Objects

Wires are used to create electrical connectivity in a schematic.

Summary

A wire is a polyline electrical design primitive that is used to form electrical connections between points on a schematic. It is analogous to a physical wire.

Availability

Wires are only available for placement in the Schematic Editor by clicking Home | Circuit Elements |  from the main menus.

Placement

After launching the command, the cursor will change to a cross-hair and you will enter wire placement mode. Placement is made by performing the following sequence of actions:

  1. Click or press Enter to anchor the starting point for the wire.
  2. Position the cursor then click or press Enter to anchor a series of vertex points that define the shape of the wire.
  3. After placing the final vertex point, right-click or press Esc to complete placement of the wire.
  4. Continue placing further wire objects, or right-click or press Esc to exit placement mode.
  5. Use the Backspace or Delete keys to remove the last wire segment placed.

While attributes can be modified during placement (Tab to bring up associated properties dialog), keep in mind that these will become the default settings for further placement.

Placement Modes

When placing a wire there are three placement modes, two of which have Start and End sub-modes. The mode specifies how corners are created when placing wires and the angles at which wires can be placed. During placement:

  • Press Shift+Spacebar to cycle through the 90 Degree, 45 Degree and Any Angle modes.
  • While in the 90 Degree or 45 Degree mode (known as true orthogonal modes), press Spacebar to cycle between the Start and End sub-modes.
  • During placement, the current placement mode is displayed in the Status bar. You can change modes at any time during wire placement.
  • In modes other than Any Angle, the line segment attached to the cursor is a look ahead segment. The segment you are actually placing precedes this look ahead segment.

 45 degree mode

 90 degree mode

 Any angle mode

Press Shift+Spacebar to cycle through the different placement modes.

Guided Wiring

Schematics have a definable electrical grid that makes it easy to define electrical connections between objects. As you are placing a wire, when the wall falls within the electrical grid range of another electrical object, the cursor will snap to the fixed object and a Hot Spot (red cross) will appear.

Hot Spot (red cross)

The Hot Spot guides you to where a valid connection can be made and automatically snaps the cursor to electrical connection points.

The electrical grid can be defined on the Sheet Options tab of the Document Options dialog (Project | Content | ). It is recommended that you set the electrical grid to be slightly smaller than the current snap grid or it becomes difficult to position electrical objects one snap grid apart.

Graphical Editing

This method of editing allows you to select a placed wire object directly in the workspace and change its size and/or shape graphically.

When a wire object is selected, the following editing handles are available:

Selected Wire, ready for graphical editing

  • Click and drag A to reposition the end points of the wire.
  • Click and drag B to move a wire vertex. The end points will remain anchored.
  • Ctrl+click and drag on a wire segment to grab that segment and reposition it. The end points and other vertices will remain anchored.
  • Right-click on a vertex point then choose the Edit Wire Vertex n command to access the Vertices tab of the Wire dialog, with the entry for the nth vertex selected ready for editing.
  • Ctrl+click and hold on a wire segment, then press Insert on the keyboard to add a vertex at that point.
  • Click and hold on a vertex, then press Delete on the keyboard to remove that vertex.

To move an entire wire, click and hold on the un-selected wire, then move to the new location.

An object that has its Locked property enabled cannot be selected or graphically edited. Double-click on the locked object directly then disable the Locked property to graphically edit the object.

A wire segment can also be removed through use of the Break Wire feature with the Cutting Length option set to Snap To Segment.

Non-Graphical Editing

The following methods of non-graphical editing are available:

Via an Associated Properties Dialog

Dialog page: Wire

This method of editing uses the Wire dialog to modify the properties of a Wire object.

The Wire dialog

The dialog can be accessed during placement by pressing the Tab key.

After placement, the dialog can be accessed in one of the following ways:

  • Double-click on the placed Wire object.
  • Place the cursor over the Wire object, right-click then choose Properties from the context menu.
The Wire dialog includes a Vertices tab, where you can edit the individual vertices of the currently selected wire object.

Via the SCH Inspector Panel

Panel page: SCH Inspector

The SCH Inspector panel enables you to interrogate and edit the properties of one or more design objects in the active document.

You are reporting an issue with the following selected text and/or image within the active document: